Challenger Lifts

4763AC SPX Fenner Stone Electric Motor 4763-AC

SPX Fenner Stone Electric Motor. Part # 4763-AC. Replaces Fenner # 2235BC & 2235CC.  Will not work if your motor is 2235-AC Why replace the whole power unit if your lift only needs a new motor? SPECIFICATIONS  - 2 Horsepower - 208-230...

JSJ4-02-09 Lock Release Sheave Pulley for Challenger E10 & E12 Lifts

JSJ4-02-09 Lock Release Pulley Sheave for the Challenger E10 & E12 lifts. This pulley also fits the Quality Q10 and Q12 models. Note: The Challenger EAK0342V14A lock release kit has updated, self-lubricating hard plastic pulleys available for your...

B1081 Challenger Screw

B-1081 Screw for arm stop bar on Challenger Lift. Fits CL series lifts. We are an authorized Challenger Distributor. Genuine Challenger Parts!

JSJ3-03-02 Cable Sheave for Challenger E10, LE10 & VLE10 Lifts X10-057

JSJ3-03-02 Cable Sheave for E10, LE10 & VLE10 Challenger Lifts. Also used on Quality Q10 lifts. Diameter of pulley is 3", with a 3/4" center hole for the JSJ4-03-03 sheave axle. This part directly replaces old Challenger part # X10-057. We are an...

JSJ4-02-08 Lock Release Pin / Axle for Challenger E-10 & E-12 Lifts

JSJ4-02-08 Lock Release Pin / Axle for Challenger E-10 and E-12 lifts. Includes washer and lock nut. We are an authorized Challenger Distributor. Genuine Challenger Parts!

JSJ5-04-00CH Equalizer Cables Pair (2) for Challenger E10, EQ10, LE10 & VLE10 Lifts

JSJ5-04-00CH Equalizer Cables for E10 Challenger Lift. Cable measures 32' 5-1/4" long.  Also used on Quality Lifts model EQ10. If you have a Challenger model LE10 or VLE10, cable part # L5-04-00CH is interchangeable with this cable! These two...

G1-1073-48 SPX Stone O-Ring Hiniker # 25010236

G1-1073-48 SPX Stone O-Ring gasket for oil reservoir or tank. 4-3/4" O.D.   Replaces Hiniker # 25010236

40053 Plastic Spacer Bearing / Wear Ring for Challenger 4 Post Lift

40053 Plastic Bearing / Wear Ring for Challenger 4 Post Lifts. Measures 4" O.D. x 1" I.D. x 1/8" thick. Used as spacer with B40050 pulley sheave. We are an authorized Challenger Distributor. Genuine Challenger Parts!

B2208 Rubber Arm Pad for Challenger Lift / Quality Lift Set of 4

Set of 4 rubber arm pads for Challenger Lifts that have the drop-in round pad assembly. Fits Models: Challenger CL10, VS10, LE10, E10 CS1020 & Quality Lifts, Launch Lifts TLT210, TLT210-AS, TLT210-XT TLT211, TLT211-AS, Ammco ACD210S, and...

17350 Challenger Screw

17350 screw for arm stop bar on Challenger Lift. We are an authorized Challenger Distributor. Genuine Challenger Parts!

4611AA Micro Switch Kit for SPX Fenner Stone Power Unit Pumps Motor Control

SPX Stone Micro Switch Kit for use with newer SPX Fenner Stone power units. Includes one each of the following: -- 4609-AA Retaining Nut-- 4610-AA Push Button Switch Holder -- 4611-AA Micro Switch 2001917-- 4612-AA Rubber Boot Button Cover

36013 Challenger Sheave Spacer Washer

36013 Challenger Sheave Spacer Washer. 1/16" thick, 1-1/2" O.D., 15/16" I.D. Fits on CL series Challenger lift models. We are an authorized Challenger Distributor.

JSJ5-02-13 Safety Release Spring for Challenger E10, E12 Lifts

JSJ5-02-13 Safety Release spring for E10 and E12 Challenger Lifts. Replaces part # X10-022. We are an authorized Challenger Distributor. Genuine Challenger Parts!

A1104 Rubber Arm Pad for Challenger Lift Set of 4

Set of 4 rubber pads for Challenger Lifts models CL-9 & CL-10 that have the 4" square pad assembly. Measures 4" x 4" and has two 1/4"-20 studs molded in the pad. Includes hardware for mounting to steel pad adjuster. We are an authorized Challenger...

W401-230 SPX Stone Micro Switch and Cover Plate & Relay 3000630

W401-230 SPX Stone micro switch and cover plate assembly with relay. Includes micro switch, switch holder, push button, rubber button cover, relay, and cover plate. Cover measures 5" x 6". Used on # 4763AC electric motor. Replaces W-400 and 3000630...

A1070TC Arm Restraint Gear for Challenger Lift

Inner Arm Restraint Gear A1070TC for Challenger CL Series lifts, including CL-9 and CL-10, and model CLFP9. New tapered style. We are an authorized Challenger Distributor. Genuine Challenger Parts!

5141AC SPX Reservoir Tank with 260185 Breather Cap

Replacement reservoir tank with breather cap for SPX Fenner Stone power unit. SPX part # 5141AC. This is used on a wide range of lifts including Challenger, Rotary, Bendpak, Bishamon, Benwil, and others. Also see part # 5279AC which is the same size...

JSJ5-08-15 Carriage Slide Blocks for Challenger E10, E12, LE10 & VLE10 Lifts

JSJ5-08-15 Slide Block for Carriage on E10, E12, LE10, and VLE10 Challenger lifts. Black plastic. Replaces old Challenger part # X10-084. We are an authorized Challenger Distributor. Genuine Challenger Parts! E-10, E-12, LE-10, VLE-10.

36025 Challenger Pulley Sheave

36025 Pulley Sheave for Challenger lift. Measures 5" O.D., 1" I.D., 1" thick with 5/16" groove. Fits Challenger Lifts model CL10, 39000, 37000, 71000 & 70000.We are an authorized Challenger Distributor.

Rubber Arm Pad for Challenger Lift Set of 4 - Replaces A1104-H

Set of 4 quality replacement rubber pads for Challenger Lifts that have the square drop in pad assembly. Measures 3-7/8" x 4", and has two bullet studs molded in the pad. Replaces A1104-H. Replace your worn out pads!!